THE RENO LEDGER
ENTRY · 22.11.2026

Stripping wallpaper in an old house

Stripping wallpaper looks like the cheapest job in the renovation, and sometimes it is. In an older house it can also be the job that opens a wall to surprises: several decades of paper, paste, paint and patching, and a lining that was never meant to get wet. A little investigation first saves a lot of repair afterwards.

Work out what you are looking at

Start at an inconspicuous edge, behind a switch plate or inside a wardrobe, and peel a corner. You are looking for three things: how many layers there are, what the backing is, and what the wall surface looks like underneath.

If the paper was hung before the 1980s, the paint underneath may also be a concern. Health NZ's lead guidance says buildings from the 1980s or earlier should be presumed to carry lead-based paint, and that you cannot tell by looking. Paper hung directly over old paint is not an exception.

Test before you steam or sand

Two materials deserve a laboratory or test-kit answer before you do anything wet or abrasive.

Lead. Wallpaper often covers painted surfaces. Steaming and scraping can pull up flakes of old paint along with the paper, and sanding the residue creates dust. Health NZ notes that hardware and paint stores sell simple lead test kits and that your local public health service can advise.

Asbestos. BRANZ's Level guide says asbestos-based products were widely used between the 1920s and mid-1980s, including wall claddings, adhesives and paints, and decorative ceilings. Wallpaper paste is not on that list, but sheet linings behind it and the paint on top of it may be, and an old textured finish on a ceiling that is being papered or re-papered is a separate question. If you have any doubt about the wall or ceiling surface, test a sample before you strip.

Information is on the Health NZ lead-based paint page and the Level asbestos page.

Why water can be the real hazard

Lining materials do not all tolerate a soaking. BRANZ's wet-area guidance, though it is written for bathrooms and kitchens, makes useful general points: standard plasterboard must be protected from direct wetting, compressed fibre-cement sheet must remain dry, and particleboard and MDF are easily damaged by moisture. Wallpaper steamers and soaking solutions apply a lot of water to a vertical surface, and plasterboard paper face can lift or soften if it gets too wet.

That has two practical consequences:

The sequence for a typical room

  1. Prepare the room. Remove curtains and furniture, cover floors, and switch off power to outlets near wet work. Isolate and tape over sockets.
  2. Test. Check for lead and, if the lining or ceiling finish is in question, asbestos, before steaming or scraping.
  3. Strip. Peel what lifts easily, score and wet the remainder, and scrape with a flexible blade held at a shallow angle so it does not gouge the lining.
  4. Remove the paste. Residual adhesive prevents paint from adhering. Wash it off with a mild solution following the product's instructions, and let the wall dry fully.
  5. Repair. Fill gouges and failed joints, and replace any lining that has been damaged beyond a repair.
  6. Seal. Plasterboard and fibre-cement substrates need sealing before they are coated. Level notes that vinyl-coated wallpaper needs a plasterboard finish stopped to at least level 3 and sealed with a water-resistant sealer before hanging, and that surfaces for paint need level 4 or 5 stopping.
  7. Finish. Prime and paint, or hang the new paper.

What if the paper will not come off

Some papers, and some old pastes on old linings, are more trouble than they are worth. If stripping would wreck the surface, there are alternatives: skim-coating a sealed surface, overlining with lining paper, or replacing the plasterboard. Those are decisions to make with whoever will paint the wall, because the final finish depends on what is underneath.

For a straightforward wall, professional wallpaper removal is usually quicker than a first attempt at it, and a good contractor will talk about testing and dust control rather than only steam.

Do you need consent?

Not for stripping and re-lining. Schedule 1 of the Building Act 2004 lists work on internal linings and finishes of walls, ceilings and floors of an existing dwelling as exempt from building consent, subject to the conditions in section 42A: the work must comply with the Building Code to the extent the Act requires, must not leave the building worse than it was, and must not breach other enactments. If the lining is part of a bracing wall or fire separation, replacing it is not a decorating job, and you should check with the council first. The Act is on legislation.govt.nz.

Clean-up and disposal

Wet paper and scrapings are heavy and messy. Bag them as you go, and keep any material that tested positive for lead separate from household waste you will put out for collection. Health NZ says small amounts of lead paint debris can go out with household rubbish or to the tip, but to check with your council if in doubt, and never burn it.

If you would rather leave the dust-managed work to someone else, specialists such as Eggshell & Co take on stripping as part of a repaint, which keeps the preparation and finishing under one roof.

Rules and guidance change, so check current versions of the sources below.

Sources

SEE ALSO: Removing a wall: load-bearing or not; Re-piling an older house: what to settle first; Paint prep in an older house: why it is most of the job
The Reno Ledger records what is worth knowing before and during the renovation of an older New Zealand house. General information; check consent rules with your council.