THE RENO LEDGER
ENTRY · 22.11.2026

Repairing or replacing old weatherboards

Weatherboards are the skin of most older Auckland houses, and they fail in two quiet ways: they rot where water sits, and they are eaten from the inside. Both can look like a tired paint job until you press a thumb into the board. Deciding between a repair and a replacement starts with working out which problem you have.

Why surface checks mislead

Consumer NZ warns that when you see borer in weatherboards there is a good chance it is more extensive than it looks, because borer tends to attack from the inside of the board. A board with a few flight holes may be hollow behind a thin skin of paint. The same source notes that borer favours the south side of buildings, where timber stays damp longer.

Probe rather than look. Push a screwdriver into the lower edge of boards, around windows, under sills and where boards meet corner boards or the bottom of a wall. Soft, spongy or crumbling timber is a sign of rot or borer damage. Look for fine dust at sheltered spots, and for small flight holes of about 2 to 4 millimetres. Mark each suspect board with chalk so you can count them: a handful of isolated boards is a repair, while a whole elevation is a larger decision.

Replace the board, treat what is behind it

Consumer NZ is direct about the long-term fix: replace the affected weatherboards and treat the framing timber behind while the wall is open. Treating only the visible board leaves the studs, nogs and the back of the neighbouring boards as a source of reinfestation. Its advice on treatment is that the only long-term option is a residual surface application that outlasts the borer life cycle, applied to bare timber, and that large infestations should be handled by a professional with the right safety equipment.

That is the main point at which a specialist can earn their fee. An assessment of borer in weatherboards that records which boards are affected and how deep the damage goes tells you whether you are replacing six boards or sixty before the scaffold goes up.

Rules on consent

MBIE's guidance on building work that does not need a consent says repair and maintenance with comparable materials is exempt, as is replacement of a component with a comparable one in the same position. Swapping a few boards for matching boards fits that description.

There are limits. The exemption does not cover repair or replacement, other than maintenance, of something that has failed its Building Code durability requirement. MBIE's example is replacing exterior wall cladding that failed within 15 years of installation and damaged the framing, which needs a consent. Large-scale replacement of cladding, or any change to the wall construction, also needs thought. The guidance says to ask the council for a discretionary exemption or apply for a consent if you are not sure.

All building work must comply with the Building Code whether or not a consent is needed.

Who is allowed to do it

Work on the outside of a building to protect it from weather counts as restricted building work, according to MBIE's guide for homeowners, and restricted work must be done or supervised by a licensed building practitioner. Licensed classes include carpenters and external plasterers. The practitioner should be able to show identification, and the public register lets you check.

Because restricted work comes with paperwork, ask for a record of work when it is done. Keep it with the house file. If you need an independent view first, a report from Lignum Timber Inspections or a similar specialist can sit beside it.

Old paint is a lead problem

Most exterior paint on an older house predates modern standards. Health NZ says buildings painted before 1980 can have lead-based paint inside and out, and that you cannot see lead just by looking. Its safety guidance names wet sanding and scraping as the preferred methods. Water-blasting and abrasive blasting are not recommended outside experienced hands, heat guns create lead fumes, and dry sanding raises a great deal of dust.

On a weatherboard job that means the ground below the wall deserves as much attention as the wall. Cover soil and plants, especially vegetable gardens, and stop flakes reaching neighbouring properties and drains. Do not burn old boards, since fumes can carry lead particles. Small amounts of paint waste can generally go with household rubbish, but large amounts should be checked with the council.

The order of the job

  1. Probe and map every suspect board.
  2. Test the paint for lead.
  3. Decide on consent and engage a licensed practitioner if the work is restricted.
  4. Remove the affected boards and inspect the framing behind.
  5. Treat exposed framing timber while the wall is open.
  6. Fit replacement boards, then paint.

Closing the wall is the point of no return. Anything wrong behind it will be sealed in for another few decades, so treat the open wall as the inspection window.

Sources

SEE ALSO: Re-piling an older house: what to settle first; Paint prep in an older house: why it is most of the job; Making good old floorboards before you sand and finish
The Reno Ledger records what is worth knowing before and during the renovation of an older New Zealand house. General information; check consent rules with your council.