THE RENO LEDGER
ENTRY · 22.11.2026

Replacing old windows and adding double glazing

Windows are the part of an old house you notice every day and the part most likely to be blamed for the cold. Replacing them is a common first renovation, and it is one of the few that has a built-in consent test based on the age of what you are removing.

Replace, retrofit or repair

Consumer NZ separates two paths. In its guide to replacing windows, retrofit double glazing installs an extra pane on the interior of existing windows. It can save money and preserve the look of your joinery, and it comes down to design ideas and whether the current windows have enough life left in them. If they are completely clapped out, replace them entirely.

For a villa or bungalow with original timber joinery, that is a real choice, not a compromise. Sound old sashes and casements can be kept, and a secondary pane adds an insulating layer. Rotten frames cannot be fixed that way.

What new windows must meet

Consumer NZ says any new windows in your place need to be double-glazed to meet Building Code requirements. That applies whether or not the work needs a consent, because MBIE is clear that all building work must comply with the Building Code. The same source describes the frame choices:

Add-ons such as argon gas or low-emissivity glass improve thermal performance but can escalate cost quickly if you fit them throughout. If the budget does not stretch, Consumer NZ suggests upgrading only the rooms you use the most.

The consent question

MBIE's guidance on building work that does not need a consent has an exemption for work in connection with a window or exterior doorway in an existing dwelling of not more than two storeys. It has two conditions: the window being replaced must not have failed its durability requirement, and the work must not modify or affect a specified system such as sprinklers or fire alarms.

In practice, windows in an external wall are generally required to last at least 15 years. If the window is older than 15 years and you are replacing it because it has rotted, no consent is needed. If it was installed within the last 15 years and has failed, replacing it does need consent, because swapping a failed window for a similar one could fail again. MBIE's example is a window fitted six years earlier that rotted and so needed a consent.

Two other points from the guidance matter in older houses:

If you are unsure whether an exemption applies, the guidance says to ask the council for a discretionary exemption or apply for a consent, rather than apply it incorrectly. Work that affects weathertightness can also be restricted building work needing a licensed practitioner, so ask whether that applies to your job.

Installation and what you find

Consumer NZ says installation usually takes a couple of days. Installers cut around the old windows and fit the new ones. You will need architraves indoors to cover the edges and painting indoors and out, which may be in the quote or left to you. It suggests taking advantage of the work to fit new flashings, which installers can do and which are not expensive.

The risk is what is behind. The same source says you will be crossing your fingers that the frames have not rotted out, and that if they have the job grinds to a halt while you find a builder to repair them. Probe the surrounding framing and the bottom of the opening before you sign for a replacement, and allow for repair as a possible extra in the budget.

Old paint on old frames

Painted timber window frames in a pre-1980 house may carry lead paint. Health NZ's lead paint guidance says buildings painted before 1980 can have lead-based paint, that you cannot tell by looking, and that wet sanding and scraping are the preferred ways to deal with it. Chemical stripping is not recommended other than by experienced renovators or professionals, and is usually for small surfaces such as window frames. Dry sanding, burning off and blowtorching are not recommended.

When the old frames are cut out, the dust and flakes still need treating as possibly lead-contaminated. Ask the installer how they will handle the removal, and keep children and pregnant women away from the work.

A sensible order

  1. Decide between retrofit, repair and replacement for each window.
  2. Test paint for lead and check for rot in frames and surrounding timber.
  3. Work out the consent position, including the 15-year test and any boundary issue.
  4. Get installers' quotes, noting what each includes: flashings, architraves, painting, making good.
  5. Fit new flashings while the openings are exposed.
  6. Finish linings and paint after installation.

Do windows after any wall repairs or re-cladding that affect the openings, and before interior painting, so you do not repaint twice.

Sources

SEE ALSO: Subfloor work during a renovation; Stripping wallpaper in an old house; Rewiring an old house
The Reno Ledger records what is worth knowing before and during the renovation of an older New Zealand house. General information; check consent rules with your council.